OpenConstruction Academy
Kirjaudu / Rekisteröidy
FI

Kurssin johdanto · 3 min

Maanrakennustyöt: leikkaus- ja täyttötilavuudet, massatasapaino ja hinnoittelu (Kanada)

Marlow Heights Phase 1 · Two new subdivision streets, Ontario · Kuvitteellinen hanke

You are the estimator for the earthworks contractor on two new streets in Ontario. Earthworks means digging soil out where the road is too high (cut) and building it up where it is too low (fill). In five tasks you measure cut and fill, convert soil between its loose and packed states, read a mass haul diagram, build a hauling rate from machine cycles and price a change for poor ground.

Aloita tehtävä 1

Work
Cut, fill, borrow (soil brought in) and haul for two streets
Contract
Municipal unit-price contract, items in the OPSS style (Ontario standard specifications)
Story
Tender in October 2026 to a change in June 2027
Työ ERP:ssä
Tehtäviä 5, noin 3 t 15 min

Kuka antaa mitä kenelle

Every arrow is a document that reaches your desk or leaves it, and the task where that happens.

Tulee sinulle

  • The Town's engineerIssues sections, checks quantities
    • Cross-sections of Heron DriveTehtävä 1
    • Mass ordinates of Marlow AvenueTehtävä 3
    • Order: silt out, Granular B inTehtävä 5
  • Site superintendentRuns the machines and trucks
    • Excavator, trucks and cycle timesTehtävä 4
SinäEstimator, earthworks contractor

Lähtee sinulta

    • Cut and fill quantitiesTehtävä 1
    • Borrow and waste quantitiesTehtävä 2
    • Overhaul and surplusTehtävä 3
    • Rate for haul to wasteTehtävä 4
    • Change for unsuitable siltTehtävä 5
    The TownOwner, pays by the unit

Reittisi hankkeen läpi

Three tasks to get the quantities right, one to price a line that has no rate, one to price a change once the ground is open. Start with task 1: in the Bill of Quantities you work out cut and fill from ten cross-sections.

  1. Quantities

    Tehtävä 1 · 35 min

    Leikkaus ja täyttö keskipinta-alamenetelmällä

    Tuotat
    Cut and fill volumes, items 02.01 and 02.02
    Asiakirja
    Ten cross-sections of Heron Drive
    ERP:ssä
    Bill of Quantities
  2. Quantities

    Tehtävä 2 · 35 min

    Paisunta, tiivistyminen ja kuorma-autokuormat

    Tuotat
    Borrow to bring in, and truck loads to take away
    Asiakirja
    Soil factors and the engineer's note on wet clay
    ERP:ssä
    Bill of Quantities
  3. Quantities

    Tehtävä 3 · 40 min

    Massatasaus, vapaa kuljetusmatka ja ylikuljetus

    Tuotat
    Overhaul (hauling beyond the free distance) and surplus, items 03.01 and 03.02
    Asiakirja
    Mass ordinates of Marlow Avenue
    ERP:ssä
    Bill of Quantities
  4. Rate

    Tehtävä 4 · 45 min

    Kaluston tuottavuudesta yksikköhintaan

    Tuotat
    The unit rate for haul to waste
    Asiakirja
    Machine costs, fuel and cycle times
    ERP:ssä
    Bill of Quantities
  5. Change

    Tehtävä 5 · 40 min

    Kelpaamaton maa-aines: hinnanmuutos

    Tuotat
    The priced change for unsuitable silt
    Asiakirja
    Test pit sections and agreed rates
    ERP:ssä
    Variations

How a cross-section becomes a price

Each column is the bill after one task. Grey is what it already holds; blue is what that task adds.

Cut and fill
Tehtävä 1Measured volumesThe areas at each end of a slice times its length give cut and fill, each in its own unit and item.
Borrow and wasteCut and fill
Tehtävä 2Borrow and wasteCut and fill compared in one state of the soil. What is short is imported, what is unusable leaves by truck.
Overhaul and surplusBorrow and wasteCut and fill
Tehtävä 3HaulDistance beyond the free haul is paid as overhaul. What is left at the end is surplus.
Haul to waste, pricedOverhaul and surplusBorrow and wasteCut and fill
Tehtävä 4A rate built upMachine output, hourly cost and the dump's gate fee give a price per bank m³ (soil as it lies in the ground).
Change for siltThe priced bill
Tehtävä 5A changeUnsuitable silt out, granular fill in, at agreed rates and without HST (sales tax).

Sininen on se, mitä tehtävä lisää; harmaa tulee aiemmasta.

Lyhyesti. Measure in bank m³. Convert only to compare or to haul. The slower machine sets the output. Price a change at the agreed rates, HST outside.