OpenConstruction Academy
সাইন ইন / নিবন্ধন
BN

কোর্সের পরিচিতি · 3 মি

রিবার টেকঅফ ও বার বেন্ডিং শিডিউল (সংযুক্ত আরব আমিরাত, BS 8666)

You are the builder's quantity surveyor on a five-storey block of flats in the UAE: you measure the work and price it. This course is about rebar, the steel bars inside the concrete. In five tasks you take the bars from the beam and slab drawings to a priced package in the bill, then value the drawing revision that changes the bar sizes.

কাজ 1 শুরু করুন

A reinforced concrete residential frame under construction, with beam and slab reinforcement being fixed on the first floor.কাল্পনিক প্রকল্প
Khor Sama ResidenceGround-plus-four residential block, UAE
Building
Ground plus four floors, concrete frame, flat slabs
Contract
FIDIC Red Book 2017 (international standard contract), with a bill of quantities, in AED
Story
March 2026 (Revision B) to June 2026 (Revision C)
ERP-তে কাজ
5টি কাজ, প্রায় 3 ঘ 40 মি

কে কাকে কী দেয়

Every arrow is a document that reaches your desk or leaves it, and the task where that happens.

আপনার কাছে আসে

  • EngineerIssues drawings and instructions
    • Beam B7 detail, Rev Bকাজ 1
    • Slab S3 detail, Rev Bকাজ 2
    • Instruction EI 07, Rev Cকাজ 5
  • Steel supplierQuotes and delivers the steel
    • Quotation per tonneকাজ 4
আপনিQuantity surveyor, main contractor

আপনার কাছ থেকে যায়

    • Measured bill linesকাজ 1
    • Package priceকাজ 4
    • Variation orderকাজ 5
    EmployerPrivate developer
    • Order quantity, waste inকাজ 3
    Your site teamPlaces the steel order

প্রকল্প ও মানুষ কাল্পনিক। প্রতিকৃতিগুলো তৈরি করা।

প্রকল্পে আপনার পথ

Two tasks measure, one weighs, one prices, one values a change. Start with task 1: in the Bill of Quantities you work out the total length of each bar in beam B7.

  1. Measure

    কাজ 1 · 45 মি

    বিম B7: শেপ কোড অনুযায়ী বার

    আপনার ফল
    Total length of each beam bar mark (each bar type on the drawing)
    নথি
    Beam B7 detail, Revision B
    ERP-তে
    Bill of Quantities
  2. Measure

    কাজ 2 · 45 মি

    স্ল্যাব S3: বার, ল্যাপ ও মেশ

    আপনার ফল
    Slab bars with laps (overlaps at joints), and mesh sheets
    নথি
    Slab S3 detail, Revision B
    ERP-তে
    Bill of Quantities
  3. Weigh

    কাজ 3 · 40 মি

    ওজন, টনেজ ও অর্ডার

    আপনার ফল
    Net tonnes by bar size, and the order
    নথি
    Mass per metre, element counts
    ERP-তে
    Bill of Quantities
  4. Price

    কাজ 4 · 40 মি

    রিইনফোর্সমেন্ট প্যাকেজের দাম নির্ধারণ

    আপনার ফল
    A rate per net tonne, and the package price
    নথি
    Supplier quotation and labour rates
    ERP-তে
    Bill of Quantities, Markups
  5. Change

    কাজ 5 · 50 মি

    Revision C: পরিবর্তন পুনঃপরিমাপ

    আপনার ফল
    The variation (priced change) for the new bar sizes
    নথি
    Engineer's instruction EI 07, Revision C
    ERP-তে
    Variations

How a drawing becomes a price

Each step below is one task, in the order the steel moves. Task 3 sits between the slab and the price: it turns metres into net tonnes, and keeps the waste for the order.

Beam bars and links, in metres
কাজ 1Cut lengthOutside dimensions, less what the bends take back, times the number of bars.
Slab bars and meshBeams
কাজ 2Slab steelBars counted by spaces rounded up, plus one, a lap at each joint, mesh laid out sheet by sheet.
Overhead and profitNet tonnes at their rates
কাজ 4Package priceNet tonnes times a rate built from supply, waste, cutting and fixing. One markup row on top.
Revision CPackage price
কাজ 5VariationNew sizes go in, old sizes come out, both at the bill rates.

নীল হলো কাজটি যা যোগ করে; ধূসর আগের ধাপ থেকে আসা।

সংক্ষেপে. Measure the bar that is bent, not the box around it. Bill net tonnes. Put the waste in the order and the supply price, the markup in one row.