OpenConstruction Academy
התחברות / הרשמה
HE

מבוא לקורס · 3 דק׳

מדידת כמויות זיון ולוח כיפוף (איחוד האמירויות, BS 8666)

You are the builder's quantity surveyor on a five-storey block of flats in the UAE: you measure the work and price it. This course is about rebar, the steel bars inside the concrete. In five tasks you take the bars from the beam and slab drawings to a priced package in the bill, then value the drawing revision that changes the bar sizes.

התחלת משימה 1

A reinforced concrete residential frame under construction, with beam and slab reinforcement being fixed on the first floor.פרויקט בדיוני
Khor Sama ResidenceGround-plus-four residential block, UAE
Building
Ground plus four floors, concrete frame, flat slabs
Contract
FIDIC Red Book 2017 (international standard contract), with a bill of quantities, in AED
Story
March 2026 (Revision B) to June 2026 (Revision C)
עבודה ב-ERP
5 משימות, כ-3 ש׳ 40 דק׳

מי מעביר מה למי

Every arrow is a document that reaches your desk or leaves it, and the task where that happens.

מגיע אליכם

  • EngineerIssues drawings and instructions
    • Beam B7 detail, Rev Bמשימה 1
    • Slab S3 detail, Rev Bמשימה 2
    • Instruction EI 07, Rev Cמשימה 5
  • Steel supplierQuotes and delivers the steel
    • Quotation per tonneמשימה 4
אתםQuantity surveyor, main contractor

יוצא מכם

    • Measured bill linesמשימה 1
    • Package priceמשימה 4
    • Variation orderמשימה 5
    EmployerPrivate developer
    • Order quantity, waste inמשימה 3
    Your site teamPlaces the steel order

הפרויקט והאנשים בדיוניים. הדיוקנאות נוצרו בתוכנה.

המסלול שלכם בפרויקט

Two tasks measure, one weighs, one prices, one values a change. Start with task 1: in the Bill of Quantities you work out the total length of each bar in beam B7.

  1. Measure

    משימה 1 · 45 דק׳

    קורה B7: מוטות לפי קוד צורה

    התוצר שלכם
    Total length of each beam bar mark (each bar type on the drawing)
    מסמך
    Beam B7 detail, Revision B
    ב-ERP
    Bill of Quantities
  2. Measure

    משימה 2 · 45 דק׳

    לוח S3: מוטות, חפיפות ורשת

    התוצר שלכם
    Slab bars with laps (overlaps at joints), and mesh sheets
    מסמך
    Slab S3 detail, Revision B
    ב-ERP
    Bill of Quantities
  3. Weigh

    משימה 3 · 40 דק׳

    משקלים, טונאז׳ וההזמנה

    התוצר שלכם
    Net tonnes by bar size, and the order
    מסמך
    Mass per metre, element counts
    ב-ERP
    Bill of Quantities
  4. Price

    משימה 4 · 40 דק׳

    תמחור חבילת הזיון

    התוצר שלכם
    A rate per net tonne, and the package price
    מסמך
    Supplier quotation and labour rates
    ב-ERP
    Bill of Quantities, Markups
  5. Change

    משימה 5 · 50 דק׳

    Revision C: מדידה מחדש של השינוי

    התוצר שלכם
    The variation (priced change) for the new bar sizes
    מסמך
    Engineer's instruction EI 07, Revision C
    ב-ERP
    Variations

How a drawing becomes a price

Each step below is one task, in the order the steel moves. Task 3 sits between the slab and the price: it turns metres into net tonnes, and keeps the waste for the order.

Beam bars and links, in metres
משימה 1Cut lengthOutside dimensions, less what the bends take back, times the number of bars.
Slab bars and meshBeams
משימה 2Slab steelBars counted by spaces rounded up, plus one, a lap at each joint, mesh laid out sheet by sheet.
Overhead and profitNet tonnes at their rates
משימה 4Package priceNet tonnes times a rate built from supply, waste, cutting and fixing. One markup row on top.
Revision CPackage price
משימה 5VariationNew sizes go in, old sizes come out, both at the bill rates.

בכחול מה שהמשימה מוסיפה; באפור מה שעבר מהשלב הקודם.

בקצרה. Measure the bar that is bent, not the box around it. Bill net tonnes. Put the waste in the order and the supply price, the markup in one row.