OpenConstruction Academy
Кіру / Тіркелу
KK

Курсқа кіріспе · 3 мин

Арматураның көлемдерін есептеу және арматураны иілу кестесі (БАӘ, BS 8666)

You are the builder's quantity surveyor on a five-storey block of flats in the UAE: you measure the work and price it. This course is about rebar, the steel bars inside the concrete. In five tasks you take the bars from the beam and slab drawings to a priced package in the bill, then value the drawing revision that changes the bar sizes.

1-тапсырманы бастау

A reinforced concrete residential frame under construction, with beam and slab reinforcement being fixed on the first floor.Ойдан шығарылған жоба
Khor Sama ResidenceGround-plus-four residential block, UAE
Building
Ground plus four floors, concrete frame, flat slabs
Contract
FIDIC Red Book 2017 (international standard contract), with a bill of quantities, in AED
Story
March 2026 (Revision B) to June 2026 (Revision C)
ERP-дегі жұмыс
Тапсырмалар: 5, шамамен 3 сағ 40 мин

Кім кімге не береді

Every arrow is a document that reaches your desk or leaves it, and the task where that happens.

Сізге келеді

  • EngineerIssues drawings and instructions
    • Beam B7 detail, Rev B1-тапсырма
    • Slab S3 detail, Rev B2-тапсырма
    • Instruction EI 07, Rev C5-тапсырма
  • Steel supplierQuotes and delivers the steel
    • Quotation per tonne4-тапсырма
СізQuantity surveyor, main contractor

Сізден кетеді

    • Measured bill lines1-тапсырма
    • Package price4-тапсырма
    • Variation order5-тапсырма
    EmployerPrivate developer
    • Order quantity, waste in3-тапсырма
    Your site teamPlaces the steel order

Жоба мен адамдар ойдан шығарылған. Портреттер генерацияланған.

Жоба бойынша жолыңыз

Two tasks measure, one weighs, one prices, one values a change. Start with task 1: in the Bill of Quantities you work out the total length of each bar in beam B7.

  1. Measure

    1-тапсырма · 45 мин

    B7 арқалығы: пішін коды бойынша стерженьдер

    Нәтиже
    Total length of each beam bar mark (each bar type on the drawing)
    Құжат
    Beam B7 detail, Revision B
    ERP-де
    Bill of Quantities
  2. Measure

    2-тапсырма · 45 мин

    S3 плитасы: стерженьдер, ұштасулар және тор

    Нәтиже
    Slab bars with laps (overlaps at joints), and mesh sheets
    Құжат
    Slab S3 detail, Revision B
    ERP-де
    Bill of Quantities
  3. Weigh

    3-тапсырма · 40 мин

    Салмақтар, тоннаж және тапсырыс

    Нәтиже
    Net tonnes by bar size, and the order
    Құжат
    Mass per metre, element counts
    ERP-де
    Bill of Quantities
  4. Price

    4-тапсырма · 40 мин

    Арматура пакетін бағалау

    Нәтиже
    A rate per net tonne, and the package price
    Құжат
    Supplier quotation and labour rates
    ERP-де
    Bill of Quantities, Markups
  5. Change

    5-тапсырма · 50 мин

    C ревизиясы: өзгерісті қайта өлшеу

    Нәтиже
    The variation (priced change) for the new bar sizes
    Құжат
    Engineer's instruction EI 07, Revision C
    ERP-де
    Variations

How a drawing becomes a price

Each step below is one task, in the order the steel moves. Task 3 sits between the slab and the price: it turns metres into net tonnes, and keeps the waste for the order.

Beam bars and links, in metres
1-тапсырмаCut lengthOutside dimensions, less what the bends take back, times the number of bars.
Slab bars and meshBeams
2-тапсырмаSlab steelBars counted by spaces rounded up, plus one, a lap at each joint, mesh laid out sheet by sheet.
Overhead and profitNet tonnes at their rates
4-тапсырмаPackage priceNet tonnes times a rate built from supply, waste, cutting and fixing. One markup row on top.
Revision CPackage price
5-тапсырмаVariationNew sizes go in, old sizes come out, both at the bill rates.

Көкпен — тапсырма қосатын бөлік; сұрмен — алдыңғы қадамнан келгені.

Қысқаша. Measure the bar that is bent, not the box around it. Bill net tonnes. Put the waste in the order and the supply price, the markup in one row.