OpenConstruction Academy
سائن ان / رجسٹر کریں
UR

کورس کا تعارف · 3 منٹ

ریبار ٹیک آف اور بار بینڈنگ شیڈول (متحدہ عرب امارات، BS 8666)

You are the builder's quantity surveyor on a five-storey block of flats in the UAE: you measure the work and price it. This course is about rebar, the steel bars inside the concrete. In five tasks you take the bars from the beam and slab drawings to a priced package in the bill, then value the drawing revision that changes the bar sizes.

ٹاسک 1 شروع کریں

A reinforced concrete residential frame under construction, with beam and slab reinforcement being fixed on the first floor.فرضی پراجیکٹ
Khor Sama ResidenceGround-plus-four residential block, UAE
Building
Ground plus four floors, concrete frame, flat slabs
Contract
FIDIC Red Book 2017 (international standard contract), with a bill of quantities, in AED
Story
March 2026 (Revision B) to June 2026 (Revision C)
ERP میں کام
5 ٹاسک، تقریباً 3 گھنٹے 40 منٹ

کون کس کو کیا دیتا ہے

Every arrow is a document that reaches your desk or leaves it, and the task where that happens.

آپ کے پاس آتا ہے

  • EngineerIssues drawings and instructions
    • Beam B7 detail, Rev Bٹاسک 1
    • Slab S3 detail, Rev Bٹاسک 2
    • Instruction EI 07, Rev Cٹاسک 5
  • Steel supplierQuotes and delivers the steel
    • Quotation per tonneٹاسک 4
آپQuantity surveyor, main contractor

آپ سے جاتا ہے

    • Measured bill linesٹاسک 1
    • Package priceٹاسک 4
    • Variation orderٹاسک 5
    EmployerPrivate developer
    • Order quantity, waste inٹاسک 3
    Your site teamPlaces the steel order

پراجیکٹ اور لوگ فرضی ہیں۔ تصاویر تیار کردہ ہیں۔

پراجیکٹ میں آپ کا راستہ

Two tasks measure, one weighs, one prices, one values a change. Start with task 1: in the Bill of Quantities you work out the total length of each bar in beam B7.

  1. Measure

    ٹاسک 1 · 45 منٹ

    شہتیر B7: شیپ کوڈ کے مطابق بار

    آپ کا نتیجہ
    Total length of each beam bar mark (each bar type on the drawing)
    دستاویز
    Beam B7 detail, Revision B
    ERP میں
    Bill of Quantities
  2. Measure

    ٹاسک 2 · 45 منٹ

    سلیب S3: بار، لیپس اور میش

    آپ کا نتیجہ
    Slab bars with laps (overlaps at joints), and mesh sheets
    دستاویز
    Slab S3 detail, Revision B
    ERP میں
    Bill of Quantities
  3. Weigh

    ٹاسک 3 · 40 منٹ

    وزن، ٹنیج اور آرڈر

    آپ کا نتیجہ
    Net tonnes by bar size, and the order
    دستاویز
    Mass per metre, element counts
    ERP میں
    Bill of Quantities
  4. Price

    ٹاسک 4 · 40 منٹ

    ریفورسمنٹ پیکج کی قیمت لگانا

    آپ کا نتیجہ
    A rate per net tonne, and the package price
    دستاویز
    Supplier quotation and labour rates
    ERP میں
    Bill of Quantities, Markups
  5. Change

    ٹاسک 5 · 50 منٹ

    ریویژن C: تبدیلی کی دوبارہ پیمائش

    آپ کا نتیجہ
    The variation (priced change) for the new bar sizes
    دستاویز
    Engineer's instruction EI 07, Revision C
    ERP میں
    Variations

How a drawing becomes a price

Each step below is one task, in the order the steel moves. Task 3 sits between the slab and the price: it turns metres into net tonnes, and keeps the waste for the order.

Beam bars and links, in metres
ٹاسک 1Cut lengthOutside dimensions, less what the bends take back, times the number of bars.
Slab bars and meshBeams
ٹاسک 2Slab steelBars counted by spaces rounded up, plus one, a lap at each joint, mesh laid out sheet by sheet.
Overhead and profitNet tonnes at their rates
ٹاسک 4Package priceNet tonnes times a rate built from supply, waste, cutting and fixing. One markup row on top.
Revision CPackage price
ٹاسک 5VariationNew sizes go in, old sizes come out, both at the bill rates.

نیلا وہ ہے جو ٹاسک شامل کرتا ہے؛ سرمئی پچھلے مرحلے سے آیا ہے۔

مختصراً. Measure the bar that is bent, not the box around it. Bill net tonnes. Put the waste in the order and the supply price, the markup in one row.