OpenConstruction Academy
Přihlásit se / Registrace
CS

Úvod do kurzu · 3 min

Výkaz výztuže a výkaz ohýbané výztuže (SAE, BS 8666)

You are the builder's quantity surveyor on a five-storey block of flats in the UAE: you measure the work and price it. This course is about rebar, the steel bars inside the concrete. In five tasks you take the bars from the beam and slab drawings to a priced package in the bill, then value the drawing revision that changes the bar sizes.

Začít úlohu 1

A reinforced concrete residential frame under construction, with beam and slab reinforcement being fixed on the first floor.Smyšlený projekt
Khor Sama ResidenceGround-plus-four residential block, UAE
Building
Ground plus four floors, concrete frame, flat slabs
Contract
FIDIC Red Book 2017 (international standard contract), with a bill of quantities, in AED
Story
March 2026 (Revision B) to June 2026 (Revision C)
Práce v ERP
Úlohy: 5, asi 3 h 40 min

Kdo komu co předává

Every arrow is a document that reaches your desk or leaves it, and the task where that happens.

Přichází k vám

  • EngineerIssues drawings and instructions
    • Beam B7 detail, Rev BÚloha 1
    • Slab S3 detail, Rev BÚloha 2
    • Instruction EI 07, Rev CÚloha 5
  • Steel supplierQuotes and delivers the steel
    • Quotation per tonneÚloha 4
VyQuantity surveyor, main contractor

Odchází od vás

    • Measured bill linesÚloha 1
    • Package priceÚloha 4
    • Variation orderÚloha 5
    EmployerPrivate developer
    • Order quantity, waste inÚloha 3
    Your site teamPlaces the steel order

Projekt i lidé jsou smyšlení. Portréty jsou vygenerované.

Vaše cesta zakázkou

Two tasks measure, one weighs, one prices, one values a change. Start with task 1: in the Bill of Quantities you work out the total length of each bar in beam B7.

  1. Measure

    Úloha 1 · 45 min

    Trám B7: pruty podle kódu tvaru

    Výstup
    Total length of each beam bar mark (each bar type on the drawing)
    Dokument
    Beam B7 detail, Revision B
    V ERP
    Bill of Quantities
  2. Measure

    Úloha 2 · 45 min

    Deska S3: pruty, přesahy a sítě

    Výstup
    Slab bars with laps (overlaps at joints), and mesh sheets
    Dokument
    Slab S3 detail, Revision B
    V ERP
    Bill of Quantities
  3. Weigh

    Úloha 3 · 40 min

    Hmotnosti, tonáž a objednávka

    Výstup
    Net tonnes by bar size, and the order
    Dokument
    Mass per metre, element counts
    V ERP
    Bill of Quantities
  4. Price

    Úloha 4 · 40 min

    Ocenění balíčku výztuže

    Výstup
    A rate per net tonne, and the package price
    Dokument
    Supplier quotation and labour rates
    V ERP
    Bill of Quantities, Markups
  5. Change

    Úloha 5 · 50 min

    Revize C: nové zaměření změny

    Výstup
    The variation (priced change) for the new bar sizes
    Dokument
    Engineer's instruction EI 07, Revision C
    V ERP
    Variations

How a drawing becomes a price

Each step below is one task, in the order the steel moves. Task 3 sits between the slab and the price: it turns metres into net tonnes, and keeps the waste for the order.

Beam bars and links, in metres
Úloha 1Cut lengthOutside dimensions, less what the bends take back, times the number of bars.
Slab bars and meshBeams
Úloha 2Slab steelBars counted by spaces rounded up, plus one, a lap at each joint, mesh laid out sheet by sheet.
Overhead and profitNet tonnes at their rates
Úloha 4Package priceNet tonnes times a rate built from supply, waste, cutting and fixing. One markup row on top.
Revision CPackage price
Úloha 5VariationNew sizes go in, old sizes come out, both at the bill rates.

Modře je to, co úloha přidává; šedě to, co se přenáší z dřívějška.

Stručně. Measure the bar that is bent, not the box around it. Bill net tonnes. Put the waste in the order and the supply price, the markup in one row.