OpenConstruction Academy
Kirjaudu / Rekisteröidy
FI

Kurssin johdanto · 3 min

Raudoituksen määrälaskenta ja taivutusluettelo (Arabiemiirikunnat, BS 8666)

You are the builder's quantity surveyor on a five-storey block of flats in the UAE: you measure the work and price it. This course is about rebar, the steel bars inside the concrete. In five tasks you take the bars from the beam and slab drawings to a priced package in the bill, then value the drawing revision that changes the bar sizes.

Aloita tehtävä 1

A reinforced concrete residential frame under construction, with beam and slab reinforcement being fixed on the first floor.Kuvitteellinen hanke
Khor Sama ResidenceGround-plus-four residential block, UAE
Building
Ground plus four floors, concrete frame, flat slabs
Contract
FIDIC Red Book 2017 (international standard contract), with a bill of quantities, in AED
Story
March 2026 (Revision B) to June 2026 (Revision C)
Työ ERP:ssä
Tehtäviä 5, noin 3 t 40 min

Kuka antaa mitä kenelle

Every arrow is a document that reaches your desk or leaves it, and the task where that happens.

Tulee sinulle

  • EngineerIssues drawings and instructions
    • Beam B7 detail, Rev BTehtävä 1
    • Slab S3 detail, Rev BTehtävä 2
    • Instruction EI 07, Rev CTehtävä 5
  • Steel supplierQuotes and delivers the steel
    • Quotation per tonneTehtävä 4
SinäQuantity surveyor, main contractor

Lähtee sinulta

    • Measured bill linesTehtävä 1
    • Package priceTehtävä 4
    • Variation orderTehtävä 5
    EmployerPrivate developer
    • Order quantity, waste inTehtävä 3
    Your site teamPlaces the steel order

Hanke ja henkilöt ovat kuvitteellisia. Muotokuvat on luotu tekoälyllä.

Reittisi hankkeen läpi

Two tasks measure, one weighs, one prices, one values a change. Start with task 1: in the Bill of Quantities you work out the total length of each bar in beam B7.

  1. Measure

    Tehtävä 1 · 45 min

    Palkki B7: tangot muotokoodin mukaan

    Tuotat
    Total length of each beam bar mark (each bar type on the drawing)
    Asiakirja
    Beam B7 detail, Revision B
    ERP:ssä
    Bill of Quantities
  2. Measure

    Tehtävä 2 · 45 min

    Laatta S3: tangot, limitykset ja verkko

    Tuotat
    Slab bars with laps (overlaps at joints), and mesh sheets
    Asiakirja
    Slab S3 detail, Revision B
    ERP:ssä
    Bill of Quantities
  3. Weigh

    Tehtävä 3 · 40 min

    Painot, tonnimäärä ja tilaus

    Tuotat
    Net tonnes by bar size, and the order
    Asiakirja
    Mass per metre, element counts
    ERP:ssä
    Bill of Quantities
  4. Price

    Tehtävä 4 · 40 min

    Raudoituspaketin hinnoittelu

    Tuotat
    A rate per net tonne, and the package price
    Asiakirja
    Supplier quotation and labour rates
    ERP:ssä
    Bill of Quantities, Markups
  5. Change

    Tehtävä 5 · 50 min

    Tarkistus C: muutoksen uudelleenmittaus

    Tuotat
    The variation (priced change) for the new bar sizes
    Asiakirja
    Engineer's instruction EI 07, Revision C
    ERP:ssä
    Variations

How a drawing becomes a price

Each step below is one task, in the order the steel moves. Task 3 sits between the slab and the price: it turns metres into net tonnes, and keeps the waste for the order.

Beam bars and links, in metres
Tehtävä 1Cut lengthOutside dimensions, less what the bends take back, times the number of bars.
Slab bars and meshBeams
Tehtävä 2Slab steelBars counted by spaces rounded up, plus one, a lap at each joint, mesh laid out sheet by sheet.
Overhead and profitNet tonnes at their rates
Tehtävä 4Package priceNet tonnes times a rate built from supply, waste, cutting and fixing. One markup row on top.
Revision CPackage price
Tehtävä 5VariationNew sizes go in, old sizes come out, both at the bill rates.

Sininen on se, mitä tehtävä lisää; harmaa tulee aiemmasta.

Lyhyesti. Measure the bar that is bent, not the box around it. Bill net tonnes. Put the waste in the order and the supply price, the markup in one row.