OpenConstruction Academy
Logi sisse / Registreeru
ET

Kursuse sissejuhatus · 3 min

Armatuuri mahuarvutus ja painutusnimekiri (AÜE, BS 8666)

You are the builder's quantity surveyor on a five-storey block of flats in the UAE: you measure the work and price it. This course is about rebar, the steel bars inside the concrete. In five tasks you take the bars from the beam and slab drawings to a priced package in the bill, then value the drawing revision that changes the bar sizes.

Alusta ülesannet 1

A reinforced concrete residential frame under construction, with beam and slab reinforcement being fixed on the first floor.Väljamõeldud projekt
Khor Sama ResidenceGround-plus-four residential block, UAE
Building
Ground plus four floors, concrete frame, flat slabs
Contract
FIDIC Red Book 2017 (international standard contract), with a bill of quantities, in AED
Story
March 2026 (Revision B) to June 2026 (Revision C)
Töö ERP-s
Ülesandeid 5, umbes 3 h 40 min

Kes annab kellele mida

Every arrow is a document that reaches your desk or leaves it, and the task where that happens.

Tuleb sinule

  • EngineerIssues drawings and instructions
    • Beam B7 detail, Rev BÜlesanne 1
    • Slab S3 detail, Rev BÜlesanne 2
    • Instruction EI 07, Rev CÜlesanne 5
  • Steel supplierQuotes and delivers the steel
    • Quotation per tonneÜlesanne 4
SinaQuantity surveyor, main contractor

Läheb sinult

    • Measured bill linesÜlesanne 1
    • Package priceÜlesanne 4
    • Variation orderÜlesanne 5
    EmployerPrivate developer
    • Order quantity, waste inÜlesanne 3
    Your site teamPlaces the steel order

Projekt ja inimesed on väljamõeldud. Portreed on genereeritud.

Sinu tee läbi projekti

Two tasks measure, one weighs, one prices, one values a change. Start with task 1: in the Bill of Quantities you work out the total length of each bar in beam B7.

  1. Measure

    Ülesanne 1 · 45 min

    Tala B7: vardad kujukoodi järgi

    Sinu tulemus
    Total length of each beam bar mark (each bar type on the drawing)
    Dokument
    Beam B7 detail, Revision B
    ERP-s
    Bill of Quantities
  2. Measure

    Ülesanne 2 · 45 min

    Plaat S3: vardad, ülekatted ja võrk

    Sinu tulemus
    Slab bars with laps (overlaps at joints), and mesh sheets
    Dokument
    Slab S3 detail, Revision B
    ERP-s
    Bill of Quantities
  3. Weigh

    Ülesanne 3 · 40 min

    Kaalud, tonnaaž ja tellimus

    Sinu tulemus
    Net tonnes by bar size, and the order
    Dokument
    Mass per metre, element counts
    ERP-s
    Bill of Quantities
  4. Price

    Ülesanne 4 · 40 min

    Armatuuripaketi hindamine

    Sinu tulemus
    A rate per net tonne, and the package price
    Dokument
    Supplier quotation and labour rates
    ERP-s
    Bill of Quantities, Markups
  5. Change

    Ülesanne 5 · 50 min

    Revision C: muudatuse uuesti mõõtmine

    Sinu tulemus
    The variation (priced change) for the new bar sizes
    Dokument
    Engineer's instruction EI 07, Revision C
    ERP-s
    Variations

How a drawing becomes a price

Each step below is one task, in the order the steel moves. Task 3 sits between the slab and the price: it turns metres into net tonnes, and keeps the waste for the order.

Beam bars and links, in metres
Ülesanne 1Cut lengthOutside dimensions, less what the bends take back, times the number of bars.
Slab bars and meshBeams
Ülesanne 2Slab steelBars counted by spaces rounded up, plus one, a lap at each joint, mesh laid out sheet by sheet.
Overhead and profitNet tonnes at their rates
Ülesanne 4Package priceNet tonnes times a rate built from supply, waste, cutting and fixing. One markup row on top.
Revision CPackage price
Ülesanne 5VariationNew sizes go in, old sizes come out, both at the bill rates.

Sinine on see, mida ülesanne lisab; hall tuleb varasemast.

Lühidalt. Measure the bar that is bent, not the box around it. Bill net tonnes. Put the waste in the order and the supply price, the markup in one row.