OpenConstruction Academy
เข้าสู่ระบบ / สมัครสมาชิก
TH

แนะนำหลักสูตร · 3 นาที

การถอดปริมาณเหล็กเสริมและตารางการดัดเหล็ก (สหรัฐอาหรับเอมิเรตส์, BS 8666)

You are the builder's quantity surveyor on a five-storey block of flats in the UAE: you measure the work and price it. This course is about rebar, the steel bars inside the concrete. In five tasks you take the bars from the beam and slab drawings to a priced package in the bill, then value the drawing revision that changes the bar sizes.

เริ่มงานที่ 1

A reinforced concrete residential frame under construction, with beam and slab reinforcement being fixed on the first floor.โครงการสมมติ
Khor Sama ResidenceGround-plus-four residential block, UAE
Building
Ground plus four floors, concrete frame, flat slabs
Contract
FIDIC Red Book 2017 (international standard contract), with a bill of quantities, in AED
Story
March 2026 (Revision B) to June 2026 (Revision C)
งานใน ERP
5 งาน ประมาณ 3 ชม. 40 นาที

ใครส่งอะไรให้ใคร

Every arrow is a document that reaches your desk or leaves it, and the task where that happens.

ส่งมาถึงคุณ

  • EngineerIssues drawings and instructions
    • Beam B7 detail, Rev Bงานที่ 1
    • Slab S3 detail, Rev Bงานที่ 2
    • Instruction EI 07, Rev Cงานที่ 5
  • Steel supplierQuotes and delivers the steel
    • Quotation per tonneงานที่ 4
คุณQuantity surveyor, main contractor

ส่งออกจากคุณ

    • Measured bill linesงานที่ 1
    • Package priceงานที่ 4
    • Variation orderงานที่ 5
    EmployerPrivate developer
    • Order quantity, waste inงานที่ 3
    Your site teamPlaces the steel order

โครงการและบุคคลเป็นเรื่องสมมติ ภาพบุคคลสร้างขึ้น

เส้นทางของคุณในโครงการ

Two tasks measure, one weighs, one prices, one values a change. Start with task 1: in the Bill of Quantities you work out the total length of each bar in beam B7.

  1. Measure

    งานที่ 1 · 45 นาที

    คาน B7: เหล็กเส้นตามรหัสรูปทรง

    สิ่งที่คุณทำ
    Total length of each beam bar mark (each bar type on the drawing)
    เอกสาร
    Beam B7 detail, Revision B
    ใน ERP
    Bill of Quantities
  2. Measure

    งานที่ 2 · 45 นาที

    แผ่นพื้น S3: เหล็กเส้น ระยะทาบ และตะแกรงเหล็ก

    สิ่งที่คุณทำ
    Slab bars with laps (overlaps at joints), and mesh sheets
    เอกสาร
    Slab S3 detail, Revision B
    ใน ERP
    Bill of Quantities
  3. Weigh

    งานที่ 3 · 40 นาที

    น้ำหนัก ปริมาณเป็นตัน และการสั่งซื้อ

    สิ่งที่คุณทำ
    Net tonnes by bar size, and the order
    เอกสาร
    Mass per metre, element counts
    ใน ERP
    Bill of Quantities
  4. Price

    งานที่ 4 · 40 นาที

    ตีราคาชุดงานเหล็กเสริม

    สิ่งที่คุณทำ
    A rate per net tonne, and the package price
    เอกสาร
    Supplier quotation and labour rates
    ใน ERP
    Bill of Quantities, Markups
  5. Change

    งานที่ 5 · 50 นาที

    การแก้ไข C: วัดปริมาณการเปลี่ยนแปลงใหม่

    สิ่งที่คุณทำ
    The variation (priced change) for the new bar sizes
    เอกสาร
    Engineer's instruction EI 07, Revision C
    ใน ERP
    Variations

How a drawing becomes a price

Each step below is one task, in the order the steel moves. Task 3 sits between the slab and the price: it turns metres into net tonnes, and keeps the waste for the order.

Beam bars and links, in metres
งานที่ 1Cut lengthOutside dimensions, less what the bends take back, times the number of bars.
Slab bars and meshBeams
งานที่ 2Slab steelBars counted by spaces rounded up, plus one, a lap at each joint, mesh laid out sheet by sheet.
Overhead and profitNet tonnes at their rates
งานที่ 4Package priceNet tonnes times a rate built from supply, waste, cutting and fixing. One markup row on top.
Revision CPackage price
งานที่ 5VariationNew sizes go in, old sizes come out, both at the bill rates.

สีน้ำเงินคือสิ่งที่งานนี้เพิ่ม สีเทาคือสิ่งที่ยกมาจากขั้นก่อน

สรุปสั้น ๆ. Measure the bar that is bent, not the box around it. Bill net tonnes. Put the waste in the order and the supply price, the markup in one row.