OpenConstruction Academy
Σύνδεση / Εγγραφή
EL

Εισαγωγή στο μάθημα · 3 λ.

Επιμέτρηση οπλισμού και πίνακας κάμψης ράβδων (ΗΑΕ, BS 8666)

You are the builder's quantity surveyor on a five-storey block of flats in the UAE: you measure the work and price it. This course is about rebar, the steel bars inside the concrete. In five tasks you take the bars from the beam and slab drawings to a priced package in the bill, then value the drawing revision that changes the bar sizes.

Έναρξη εργασίας 1

A reinforced concrete residential frame under construction, with beam and slab reinforcement being fixed on the first floor.Φανταστικό έργο
Khor Sama ResidenceGround-plus-four residential block, UAE
Building
Ground plus four floors, concrete frame, flat slabs
Contract
FIDIC Red Book 2017 (international standard contract), with a bill of quantities, in AED
Story
March 2026 (Revision B) to June 2026 (Revision C)
Εργασία στο ERP
5 εργασίες, περίπου 3 ώ. 40 λ.

Ποιος δίνει τι σε ποιον

Every arrow is a document that reaches your desk or leaves it, and the task where that happens.

Έρχεται σε εσάς

  • EngineerIssues drawings and instructions
    • Beam B7 detail, Rev BΕργασία 1
    • Slab S3 detail, Rev BΕργασία 2
    • Instruction EI 07, Rev CΕργασία 5
  • Steel supplierQuotes and delivers the steel
    • Quotation per tonneΕργασία 4
ΕσείςQuantity surveyor, main contractor

Φεύγει από εσάς

    • Measured bill linesΕργασία 1
    • Package priceΕργασία 4
    • Variation orderΕργασία 5
    EmployerPrivate developer
    • Order quantity, waste inΕργασία 3
    Your site teamPlaces the steel order

Το έργο και τα πρόσωπα είναι φανταστικά. Τα πορτρέτα είναι παραγόμενα.

Η διαδρομή σας στο έργο

Two tasks measure, one weighs, one prices, one values a change. Start with task 1: in the Bill of Quantities you work out the total length of each bar in beam B7.

  1. Measure

    Εργασία 1 · 45 λ.

    Δοκός B7: ράβδοι ανά κωδικό σχήματος

    Παράγετε
    Total length of each beam bar mark (each bar type on the drawing)
    Έγγραφο
    Beam B7 detail, Revision B
    Στο ERP
    Bill of Quantities
  2. Measure

    Εργασία 2 · 45 λ.

    Πλάκα S3: ράβδοι, ματίσεις και πλέγμα

    Παράγετε
    Slab bars with laps (overlaps at joints), and mesh sheets
    Έγγραφο
    Slab S3 detail, Revision B
    Στο ERP
    Bill of Quantities
  3. Weigh

    Εργασία 3 · 40 λ.

    Βάρη, τονάζ και η παραγγελία

    Παράγετε
    Net tonnes by bar size, and the order
    Έγγραφο
    Mass per metre, element counts
    Στο ERP
    Bill of Quantities
  4. Price

    Εργασία 4 · 40 λ.

    Τιμολόγηση του πακέτου οπλισμού

    Παράγετε
    A rate per net tonne, and the package price
    Έγγραφο
    Supplier quotation and labour rates
    Στο ERP
    Bill of Quantities, Markups
  5. Change

    Εργασία 5 · 50 λ.

    Revision C: επανεπιμέτρηση της μεταβολής

    Παράγετε
    The variation (priced change) for the new bar sizes
    Έγγραφο
    Engineer's instruction EI 07, Revision C
    Στο ERP
    Variations

How a drawing becomes a price

Each step below is one task, in the order the steel moves. Task 3 sits between the slab and the price: it turns metres into net tonnes, and keeps the waste for the order.

Beam bars and links, in metres
Εργασία 1Cut lengthOutside dimensions, less what the bends take back, times the number of bars.
Slab bars and meshBeams
Εργασία 2Slab steelBars counted by spaces rounded up, plus one, a lap at each joint, mesh laid out sheet by sheet.
Overhead and profitNet tonnes at their rates
Εργασία 4Package priceNet tonnes times a rate built from supply, waste, cutting and fixing. One markup row on top.
Revision CPackage price
Εργασία 5VariationNew sizes go in, old sizes come out, both at the bill rates.

Με μπλε ό,τι προσθέτει η εργασία· με γκρι ό,τι έρχεται από πριν.

Με λίγα λόγια. Measure the bar that is bent, not the box around it. Bill net tonnes. Put the waste in the order and the supply price, the markup in one row.